The New NACE-CIP2-001 2026 Updated Verified Study Guides & Best Courses
Authentic NACE-CIP2-001 Exam Dumps PDF - 2026 Updated
NEW QUESTION # 21
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to scope of your role
- B. Review the NACE Attestation prior to making a decision
- C. Advise the prospective employer that you cannot accept the position
- D. Accept assignment without hesitation
Answer: B
NEW QUESTION # 22
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. a), b), and c)
- B. Risk of chemical exposure
- C. Risk of acid or caustic splashes
- D. Risk of skin
Answer: A
NEW QUESTION # 23
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Don your air supplied respirator and continue the testing
- B. Exit the tank and immediately and report the problem to the nearest safety supervisor
- C. Exit the tank and document the incident in your daily report
- D. Investigate to find the source of the odor
Answer: B
NEW QUESTION # 24
Application of Thermal Spray Coatings requires:
- A. The same skills as liquid coatings
- B. The same skills as welding
- C. Specialized skills supported by training and experience
- D. No particular skills
Answer: C
NEW QUESTION # 25
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 3-Layet Polyethylene (PE)
- B. 2-Layet Polyethylene (PE)
- C. Concrete
- D. Coal Tar Enamel
Answer: C
NEW QUESTION # 26
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A mechanical adhesion tester
- C. A destructive paint inspection Tooke gauge
- D. A set of 14 pencils of varying hardness
Answer: C
NEW QUESTION # 27
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION # 28
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Iron content
- C. Appearance
- D. Safety
Answer: B
NEW QUESTION # 29
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It contains biocide
- D. It doesn't contain biocide
Answer: C
NEW QUESTION # 30
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Consult the specification to determine how they should be treated
- C. Write an NCR and call the fabricator
- D. Stop the job immediately
Answer: B
NEW QUESTION # 31
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. mild steel.
- C. iron
- D. aluminum
Answer: A,D
NEW QUESTION # 32
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Adhesion failure
- B. Glue failure
- C. Cohesion failure
- D. Cold flow or creep
Answer: D
NEW QUESTION # 33
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. powder coatings.
- C. inorganic zincs.
- D. urethanes.
Answer: C
NEW QUESTION # 34
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. At the pre-job conference
- C. By the contractor
- D. In the specification
Answer: D
NEW QUESTION # 35
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. No difference from any other coating
- C. A very high reading
- D. Cold flow or creep
Answer: D
NEW QUESTION # 36
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. More challenging than coating steel
- C. Less challenging, than coating steel
- D. The same as coating steel
Answer: B
NEW QUESTION # 37
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Advise the coating applicator supervisor of your readings
- C. Check to See if the dehumidification equipment is operating correctly
- D. Call your supervisor
Answer: B
NEW QUESTION # 38
In the event of a conflict between the Product Data Sheet and the Specification:
- A. The Product Data Sheet prevails
- B. It is up to the Applicator to decide which one to follow
- C. It is up to the Inspector to decide which one to follow
- D. The Specification prevails
Answer: D
NEW QUESTION # 39
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that have been modified for concrete
- C. Methods that are the same as wood
- D. Methods that are completely different to steel
Answer: B
NEW QUESTION # 40
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 35 single rubs with a saturated cloth.
- B. 25 double rubs with a saturated cloth.
- C. 50 double rubs with a saturated cloth.
- D. 25 single rubs with a saturated cloth.
Answer: C
NEW QUESTION # 41
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Structural integrity
- B. Air changes
- C. Lighting
- D. a), b), and c)
Answer: D
NEW QUESTION # 42
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Stoning
- B. Sacking
- C. Acid etching
- D. High-pressure water washing
Answer: B
NEW QUESTION # 43
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Coalescence
- C. Co-Reaction
- D. Oxidation
Answer: B
NEW QUESTION # 44
......
NACE-CIP2-001 (Coating Inspector Level 2) Certification Exam is a globally recognized certification program offered by the National Association of Corrosion Engineers (NACE). NACE-CIP2-001 exam is designed to evaluate the knowledge and skills of individuals involved in the inspection and management of coating projects. Coating Inspector Level 2 certification program is widely recognized by industries such as oil and gas, marine, aerospace, and construction, and is a valuable credential for professionals seeking advancement in their careers.
Becoming a NACE-CIP2-001 certified coating inspector can lead to many career opportunities in the coatings industry. Coating Inspector Level 2 certification demonstrates a high level of expertise and knowledge, making it highly sought after by employers. It can also lead to higher salaries and greater job security. Additionally, certification holders are required to maintain their certification through continuing education and recertification exams, ensuring that they stay up-to-date with the latest industry standards and best practices.
Get Prepared for Your NACE-CIP2-001 Exam With Actual 100 Questions: https://pass4sure.practicetorrent.com/NACE-CIP2-001-practice-exam-torrent.html